Be wise with your finances.
Years ago I was intrigued with a lazy girl pattern. I have not seen it in my local quilt shops lately, but found this link to the wonder wallet on line. Perfect scrap project!
After making many of them for gifts, I noticed that there was a significant amount of wear at the corners. So I thought that interfacing the entire outside of the wallet would be a good idea.
Also with the multi layers of fabric that bottom of the little wallet got super bulky really quickly, causing more wear on the wallet, and my supply of sewing machine needles.
So after much thought I made some revisions to how I constructed this little gem.
If the cover of the wallet wraps all the way around and all the raw edges of the pockets are enclosed in top stitching on the bottom, that would solve the bulk/wear/and corner turning problems I had encountered with the original design.
First, find three small prints that coordinate nicely. I used these from Cotton and Steel that I found at my LQS.
Cut the outer layer and lower pocket 5.5 x 16 inches. medium pocket 5.5 x 5 inches and tall pocket 5.5 x 6 inches. I used a woven fusible interfacing, which I cut the same size as the outer layer and lower pocket, and two pieces that were 5.5 x 2.5 and 5.5 x 3 respectively. Cut a 1.5 inch strip of hook and loop tape.
Fuse the interfacing to the wrong sides of the fabric, for the two smaller pieces, fold them in half and give them a nice press so that you can see where to apply that interfacing on one half of the piece. Make sure that they are still 5.5 inches wide! With these two pieces folded in half, edge stitch along the folded edge.
On the largest piece. Mark a light pencil line four inches from the bottom of the longer piece on the wrong side of the fabric. Fold up the raw edge to meet this line. It will look like a two inch hem. Then bring the raw edge of the other end to meet the first raw edge, and press. The piece with both edges folded in will measure 5.5 x 8 inches.
Fold it in half lengthwise, and mark 3/4 inch from the fold on both layers, both top and bottom of each end. This is so the velcro can be centered.
Place the cover on the table with the folded raw edges down and the smooth side up. On the side with the two inch fold, pin the soft side of the hook and loop tape to the edge of the cover between your markings.
Start stitching on the edge, like you would top stitch straight across, get to the hook and loop tape, stitch across it, and just before you get to the end of the tape, stop with the needle down, pivot and sew across the short edge of the tape, back across the bottom and up to the top again. Then edge stitch to the other end of the line.
This puts a double line of stitching across the top of the velcro strip. with a loop around the lower part of the velcro, and will secure it in place.
Layer the other two pocket layers behind the short one with the velcro attached. Pin only the pocket layers, so that the three layers move independently from the rest of the wallet. It is important here, that you pin from the outside in, and that your pin heads are hanging over the outside of the fabric. Flip this pocket layer down, and back around to the other side of the wallet. You will only see the the back of the tallest pocket from this angle.
Next, take the six inch flap and bring it up and back over itself, so that all you see is interfacing on either side. add two more pins that also are pinned from the outside in. from the side it will look like this:
The bottom of the little wallet will look like this with multiple raw edges and folds.
Stitch the longer sides with a scant 1/4 inch seam.
Remove your pins and start turning right side out by lifting the top layer over the whole assembly and pulling what is left out from under it. Poke out the corners with a chopstick or other handy turning tool. It will look like a bit of a mess. We will need to do some turning. Find the pockets and flip them over to the other side, poke out some more corners and here you are!
Top stitch the edges starting at the top of the pockets, and when you get to the top, be sure to loop Around all four edges of the corresponding part of the hook and loop tape in the center on the edge that would fold down to meet its counterpart.